Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Folsom?
Gate access control work in Folsom typically runs $275 to $950 for repairs to keypads, loop detectors, control boards and actuators, and $1,400 to $4,800 for a full access-control install on an existing gate. The number that lands on your written estimate depends on whether we’re replacing one component or building out the entry system from the operator up. Either way, the estimate is free and the price is set per job once we’ve looked at your gate.
Folsom has a specific mix that drives these numbers. You’ve got older established neighborhoods where a driveway gate has been running on the same operator since the house was built, and newer hillside properties in the Folsom Ranch area where the gate was installed with the landscaping. Those two situations price very differently. An old Linear or LiftMaster control board that’s been baking in a south-facing cabinet for years often needs replacement, not adjustment. A newer FAAC or BFT slide operator that’s just out of alignment usually needs a service visit. We’re a dedicated gate repair company, and every job we take is a gate job, which means we recognize the failure pattern by brand before we open the cabinet.
Key Takeaways
- Typical repair range in Folsom: $275 to $950, depending on the component.
- Full access-control install on an existing gate: $1,400 to $4,800.
- Keypad and entry-device replacements are usually the cheapest line items at $275 to $650.
- Control board replacement runs $450 to $1,100, higher on commercial DoorKing units.
- Estimates are free, and the written estimate sets the final price. Call (833) 593-3926.
Gate Access Control Cost Breakdown (2026)
Here’s how the line items break out for Folsom properties in 2026. These are typical ranges for the local market, not quotes. Your written estimate is the only number that counts.
| Access Control Item | Typical Folsom Range | What It Covers |
|---|---|---|
| Keypad or entry device replacement | $275 – $650 | Removing the failed keypad, wiring and programming the replacement, testing codes |
| Loop detector diagnosis and repair | $300 – $800 | Testing the buried loop, replacing the detector board, re-tuning for your gate’s traffic |
| Control board replacement | $450 – $1,100 | New board, reprogramming travel limits and safety inputs, full function test |
| Actuator or arm replacement (swing gate) | $550 – $1,300 | Removing the failed arm, mounting and aligning the replacement, setting force limits |
| Safety photo-eye or edge sensor set | $350 – $850 | New sensors, alignment, wiring into the operator’s safety circuit |
| Full access-control install (existing gate) | $1,400 – $4,800 | Keypad, entry device, loop or sensor package, wiring run, programming, commissioning |
| Commercial high-cycle access upgrade | $2,800 – $7,500 | DoorKing or FAAC grade controls, multi-device entry, loop logic for property manager use |
What pushes a job toward the top of a range: buried loop wire that needs to be re-run rather than re-tuned, a control cabinet that’s been exposed to direct afternoon sun and cooked its board, or a commercial gate used by dozens of vehicles a day where the entry logic has to be rebuilt from scratch. What keeps a job at the bottom: a keypad that simply lost its programming, a photo-eye knocked out of alignment by a landscaper, or a swing arm that needs its limits reset. The single biggest cost driver we see in Folsom is whether the failure is in the access-control hardware itself or in the operator behind it. A gate that “won’t open” is often an operator problem that shows up as an access-control symptom.
What Affects Gate Access Control Pricing in Folsom
- Gate type and weight. A residential swing gate on a Ghost Controls or Mighty Mule operator carries lighter access hardware than a commercial slide gate heavy enough to need a DoorKing controller. Heavier gates need heavier controls, and the price follows.
- Brand of the existing system. LiftMaster and Linear residential systems are common in Folsom’s older subdivisions, and parts are straightforward. FAAC and BFT systems in newer hillside properties are professional-grade and cost more to service, but they’re also more forgiving of daily use. We work on all nine of these systems by name.
- Wiring condition. If the low-voltage wire to your keypad or loop has been chewed, nicked by a string trimmer, or run through soil that shifts, replacing the device won’t fix anything until the wire is dealt with. That’s a real line item.
- Age of the operator. On a gate installed in the 1990s, access-control upgrades often make more sense bundled with an operator replacement than as a standalone job. We handle repair and installation under one roof, so you don’t have to call a second company when a repair reveals the operator is on its way out.
- Commercial vehicle traffic. Property managers with a loop detector at a high-traffic entry need a detector tuned for constant use, not a residential unit pushed past its rating. Commercial access-control work prices differently from residential.
- Whether power is already at the gate. A gate post that already has power and a control cabinet is a much simpler access-control install than one where we’re running new conduit. The site visit tells us which one you have.
Repair or Replace? The Access-Control Question
For most Folsom gates, repairing the access-control component is the cheaper answer and the right one. A keypad that’s failed after years in the sun is a $275 to $650 fix. Replacing the whole system because of it wastes money. But there’s a threshold. When the control board is gone, the loop is failed, the keypad is dead and the operator is old enough that parts are getting scarce, replacing the access-control package and the operator together is often the better call. Ask for both numbers on your estimate and compare them honestly. We give you the repair price and the replace price side by side, and you decide.
The same logic applies to commercial sites. A property manager running a DoorKing system at a shared entry wants the access-control side repaired, not the entire gate torn out and replaced. That’s within reach. A commercial operator that’s cycling hundreds of times a day and starting to stall is a different conversation. Either way, the first visit is diagnostic, the estimate is free, and nothing gets replaced until you’ve signed off on the number.
How to Save on Gate Access Control
Get the diagnosis right the first time. The most expensive access-control job is the one that gets fixed twice. A technician who spends the first visit guessing at the keypad when the real fault is in the loop detector will cost you a second visit and a second part. That’s why we lead with brand recognition: when we open a FAAC cabinet or a Linear control box, we’re reading familiar circuitry, not a manual we downloaded on the way over.
- Describe the symptom precisely. “The gate won’t open from the car” is different from “the keypad won’t take the code.” Both are access-control symptoms, and both point to different parts. The more specific you are on the call, the faster the diagnosis.
- Don’t replace the keypad if the wire is bad. Ask us to test the wire first. It’s a quick check and it can save you the cost of a device you didn’t need.
- Bundle the free estimate visit. If you mention both issues – the failing keypad and the slow operator – on the first call, we’ll price both together. The estimate is free and there’s no fee for a second look at a related component during the same visit.
- Look at the operator, not just the control. An access-control failure that keeps coming back is usually an operator problem in disguise. Fixing the root cause once costs less than three return visits to the keypad.
- Use one gate company from diagnosis to install. If a repair uncovers a bigger problem, the same team handles the replacement. You’re not paying for a second company to learn your gate from scratch.
For a free estimate on your Folsom gate, call (833) 593-3926. We answer 24/7, dispatch runs 7am to 7pm Sunday through Friday, and we’re closed on Saturday.
FAQs – Gate Access Control Cost
How much does a keypad replacement cost in Folsom?
Keypad replacement in Folsom typically runs $275 to $650, including removal, wiring and programming of the new device. The range reflects the device grade and whether the existing low-voltage wire is sound. Call (833) 593-3926 for an exact quote on your gate.
How much does it cost to fix a gate loop detector in Folsom?
Loop detector repair in Folsom usually falls between $300 and $800. If the buried loop itself has failed and needs to be cut and re-run, expect the higher end; a detector board swap is closer to the lower end. Estimates are free, so call (833) 593-3926 and we’ll price it properly.
Is it cheaper to repair or replace gate access control in Folsom?
Repair is almost always cheaper, with component repairs in Folsom running $275 to $950 versus $1,400 to $4,800 for a full access-control install. Replacement only wins when the control board, loop and entry device have all failed on an aged operator. Call (833) 593-3926 and we’ll quote both so you can compare.
How much does a commercial gate access-control system cost in Folsom?
Commercial access-control work on a DoorKing or FAAC system in Folsom typically runs $2,800 to $7,500 for a high-cycle entry upgrade with multi-device access and loop logic. That covers hardware, wiring and commissioning on a gate already in place. Call (833) 593-3926 to schedule a site visit for property managers.
Can you fix my gate access control the same day in Folsom?
Yes, in most cases. Keypad, photo-eye and detector-board failures are common same-day fixes when the part is on the truck and the fault is straightforward. Call (833) 593-3926. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, and we’re closed on Saturday.
Why Folsom Gate Owners Call Us
Gate Repair Folsom has focused exclusively on gates since 2014. That’s twelve years of working on the same systems our Folsom customers actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite and Mighty Mule. We repair and install, and we do both on the same visit when a repair uncovers a bigger problem. Whether you need a keypad swapped or a full access-control install on an existing gate, we’re set up for it.
If you’re not sure whether your gate needs access-control work at all, visit Gate Repair Folsom to see how we approach diagnosis, or check our coverage for Folsom to confirm we serve your address. Most access-control jobs start with one phone call and end with a written estimate you can act on. No diagnostic fee. No pressure. Call (833) 593-3926 for a free estimate.
Pricing reflects the Folsom market as of 2026. Gate Repair Folsom offers free estimates – call (833) 593-3926.
What Our Customers Say
"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
- Adam Miller"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
- Brandon Lin"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Sofia Torres